1260 0 Posted October 17, 2020 Share Posted October 17, 2020 Hi guys Thank you for my welcome. Any ideas please? My boys SH125 is reluctant to start. Once running will only tick over with throttle half open, will run but cuts out. We've changed throttle body, no change. Cleaning out the injector and will try again later also changed plug for a new one. Would really appreciate any further ideas Cheers Mart Link to post
dave 963 Posted October 17, 2020 Share Posted October 17, 2020 It could be the sign of a tight tappet, easy to do on the SH. make sure the plug cap it pressed fully home. 1 1 Link to post
MatBin 5,081 Posted October 17, 2020 Share Posted October 17, 2020 (edited) Air filter? Plug condition/sooted up? Edited October 17, 2020 by MatBin 1 Link to post
1260 0 Posted October 17, 2020 Author Share Posted October 17, 2020 Dave and Mattb thanks will try each. 👍 Link to post
SteveThackery 3,090 Posted October 17, 2020 Share Posted October 17, 2020 This is such a difficult question, because in reality it COULD be dozens of things - diagnosis over the Internet is really hard. The proper way to address any fault like this is to follow a logical sequence of diagnostic steps, which would include looking at any fault codes recorded. Without having the bike in front of us all we can do is throw out suggestions. It has fuel injection, you say? Sensor malfunctions can lead to this kind of fault. I know nothing about the SH125, but ones to check would be the throttle position sensor (TPS), the engine temperature sensor, and the manifold absolute pressure sensor (MAP). However, mostly (but not always) you'd get the MIL (malfunction indicator light) lit on the dashboard. Mechanical problems which can cause similar problems are low fuel pressure, and this is certainly a possibility. You should check the fuel pump and the pressure dump valve for correct operation, and also check the fuel strainer to see if it is blocked. All of these are inside the fuel tank. If you can get a Haynes manual, or the official service manual, they should contain the information you need to check the above things. Finally, if there are any pipes or tubes connected to the intake manifold, check that none have fallen off or split. 2 1 Link to post
Tex 36,817 Posted October 17, 2020 Share Posted October 17, 2020 48 minutes ago, SteveThackery said: Finally, if there are any pipes or tubes connected to the intake manifold, check that none have fallen off or split. Actually, do that first. An air leak will give you all sorts of problems and can be a bugger to find. 2 1 Link to post
dave 963 Posted October 17, 2020 Share Posted October 17, 2020 Good post Steve. I assumed the the light was not on. Being a scooter problems sometimes are caused by motorcycle shops not wanting to work on scooters. 1 Link to post
trisaki 2,029 Posted October 17, 2020 Share Posted October 17, 2020 Valve clearances and a good check over for split vacuum pipes 1 Link to post
Defender 3,837 Posted October 17, 2020 Share Posted October 17, 2020 5 hours ago, Tex said: Actually, do that first. An air leak will give you all sorts of problems and can be a bugger to find. Yes, oh so very true, I had that issue on an XJ600 (1st generation) inlet rubber had gone porous! It was weakening the mixture, so it would start with some help from damp start (or similar) but once that was combusted it needed a lot of throttle ie. fuel for it to run? 1 1 Link to post
1260 0 Posted November 4, 2020 Author Share Posted November 4, 2020 Guys thank you. Trying all suggestions. Had the injector out. Cleaned it fuel in a 30 degree spray pattern on turning over to start plenty of fuel until I twist the throttle, then it cuts off the fuel to the injector? Link to post
kayz1 2,928 Posted November 4, 2020 Share Posted November 4, 2020 Check the throttle position doda thingy.. My T-MAX did that some years ago..Had to buy a new throttle Body complete for that. 1 Link to post
kayz1 2,928 Posted November 5, 2020 Share Posted November 5, 2020 Just had another thought, My T-MAX would start ok but die when the throttle was opened end a little. Link to post
1260 0 Posted November 7, 2020 Author Share Posted November 7, 2020 Kayz1 Cheers we put a second hand one on but lookalike it's a dud too. May have to go new with this. 👍 Link to post
donkeyrideruk 0 Posted June 4, 2021 Share Posted June 4, 2021 What year is the Honda sh? 2013-2014 There was a recall - fuel pump inlet cover swelling. It has been identified that there could be a defect with the Fuel pumps inlet cover. Subsequently, the engine may be difficult to start and / or the engine may stall without warning from fuel starvation and will be impossible to restart. hope this helps Link to post
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now