All Activity
- Past hour
-
HMLTL joined the community
-
p.s. They received the forks from me. Then started the job on Monday and I was refitting them on Thursday. Tremendous service!
-
Yes. I sent my forks to Maxton and they did all the internals. They set the pre-load based on my weights. The adjusters are located internally, accessible with the top caps removed. But the sags seem to be correct.
- Today
-
Thanks. MIght get my forks done the same one day Did Maxton make the internal fork mods? No external fork preload adjusters then?
-
Vince0351 joined the community
-
Thanks for sharing all that @oldwisedudevery informative and interestingšš
-
As with most stock bikes, our NC's suspension is a compromise. Honda and Showa have cunningly attempted a one-size-fits-all system, using progressive springs and unsophisticated damping, to keep costs down. The bikes tend to be under-sprung and over-damped. To address these shortcomings, I fitted the Maxton SD20 front fork legs and the NR4 rear shock to my 2023 NC750X-DCT two days ago. Installation was straightforward. I had ensured that the bike had not moved at all since I removed the original forks and shock. Consequently the Maxton shock fitted perfectly, having exactly the s
-
No
- Yesterday
-
fitted anything to hbars, fitted handguards or affected the weights inside the hbars
-
Omar joined the community
-
For disambiguation. In this case 'hard' should be read as difficult to achieve.
-
You demon of the speed sirā¦..šš
-
Thank you for that sir
-
Just checking and Smith & Allen is also recommended by some here and that's still Ā£25 https://www.that auction site.co.uk/itm/304236729637
-
https://www.that auction site.co.uk/itm/121756857457 Sorry it's gone up Ā£2 since I last ordered, I've done three oil changes using this and I know a few others on here also use it.
-
Sorry should have put where do i get that from please
-
Where do i get from please
-
Any leaks from the forks? When I rebuilt my forks there was hardly any fluid left in one leg and it tended to waggle a bit under hard acceleration.
-
dave addy joined the community
-
Agreed, every bike I have had exhibits this when hands off the bars, but it was always so slight if I had my hands on the bars I couldn't feel it.
-
Trev started following Handle bars shake? and Handle bars shake?
-
Unlikely but losing a wheel balance weight (black stick on in my case) would also cause shakes.
-
@Grumpy old man, every bike Iāve had has done a version this, usually around 40 to 35 mph slowing down with hands off the bars. Including my NC. Having a load up in the top box and or panniers can make it worse, it usually does. A heavy tank bag can improve it. Itās part of the compromise the designer has between stability and easy steering, the relationship between rake and trail. In simple terms, long trail more stable, heavier steering, short rake light steering less stable. Nothing to worry about, the designer intentionally allowed for the rider holding on with both hands, keeps the
-
Thanks Trev, it's been there a while that I know of but it might have been there even before just wasn't aware as I hadn't removed my hands from the bars. It's had different makes of tyres that hasn't made a difference but I've never played with the pressure on the front always 36psi. I'll have a play. Thanks.
-
Interesting Thanks
-
Almost every bike I've owned has had a 'shake' when slowing down (it's hard to speed up with no hands on the bars ). Usually somewhere between 35 and 50mph, depending on the bike. Just let the bike ride through it and it'll sort itself out. A 'shake' on accelerating, with hands on the bar, on the other hand is definitely an issue!
-
dont let go of the bars no charge seriously though just check TP and adjust slightly up or down
-
Was the shake there before the new tyres were fitted? In my experience, unless the bike basically has a 'twitchy' setup, which the NC does not, then it will be tyres and/or pressures causing it.
-
I have it and have used it but I haven't had issues with DCT or ABS, yet.. I have a feeling it might not report DCT or ABS stuff as the engine data it reports is generic and as far as i can tell not model specific. For example it has VTEC parameters which will only apply to a small number of bikes. But it might still report DTC codes for DCT.
-
Hi All, Once again I'm asking this question. My bike a 2015 750x has a handle bar shake in the 45-50 mph range but only if I let go of the bars, just rest my finger on the bars and it goes. What causes it, I've had two new tyres and balancing, I've checked, greased and adjusted head bearings, new disc and pads, wheel bearings are good, I've tried adjusting rear preload up and down but to no affect. Any suggestions? Thanks