ncmf 87 Posted July 15, 2016 Share Posted July 15, 2016 Not for an NC. This is for an xr125. How to get them on without puncturing the tube? I have just put one on and it was very tight. I remember mx tyres being a lot looser but this one was a real pain. In the fight to get it on I punctured it. I knew i would have done it even before I tried to blow it up. Is there a trick to it? Would inflating the tube a little help keep it away from the levers? Link to post
Tex 36,817 Posted July 15, 2016 Share Posted July 15, 2016 Starting with the tyre completely off the rim, put the tube into the tyre and inflate it until it 'fills' the space but is still 'soft'. Push the valve through the hole in the rim and then fit the first (easy) side of the tyre. Turn the wheel over, use liquid soap (or proper tyre fitting stuff if available). Using your fingers only (no levers) fit the first part of the bead into the rim. Make sure the bead is pushed right into the well of the rim and, slowly, work your way round. You may need to use levers for the last couple of inches. It's easy to do, hard to describe. Practice makes perfect.. 2 Link to post
ncmf 87 Posted July 15, 2016 Author Share Posted July 15, 2016 Thanks Tex. I'll have another go when the new tubes arrive. Link to post
Guest bonekicker Posted July 16, 2016 Share Posted July 16, 2016 As Simon say's the Trick is to inflate the tube slightly and use washing up liquid--I did the same yesterday to grandkids push bikes--after fixing yet another few punctures--the inner tubes are looking like patchwork quilts--there will be no room left for any more patches soon --and the tubes have tripled in weight Link to post
trisaki 2,029 Posted July 16, 2016 Share Posted July 16, 2016 If you use leversome make sure they are very smooth and the end nice and round Link to post
Tonyj 6,907 Posted July 16, 2016 Share Posted July 16, 2016 You tube is your best point of reference. I've found through experience the bead has to be in the well of the tyre or you really struggle pulling the tyre over the rim. Some air in the tube ,5psi plus minus and little bites as you go round . Don't put air in until tube is inside tyre on rim Link to post
Tonyj 6,907 Posted July 16, 2016 Share Posted July 16, 2016 (edited) Just read tex's advice , that's about it really Edited July 16, 2016 by Tonyj Link to post
embee 7,288 Posted July 16, 2016 Share Posted July 16, 2016 (edited) I usually put the first side of the tyre onto the rim, then fit the tube into it. Sometimes it can be tricky to get the valve into the hole if the tyre beads are a bit stiff. Once inside the tyre, put just enough air in the tube to stop it folding and getting trapped between rim and bead. Then starting opposite the valve start fitting the second bead, working equally round each side ending up at the valve. The key is indeed getting the bead fully down into the well on the opposite side as you approach the last bit, too much air in the tube will stop you achieving this. I'd definitely recommend getting proper tyre lube. I got some of this http://www.demon-tweeks.co.uk/mx-off-road/tubes-mousses/pro-clean-tyre-lube for the last tyres I fitted and have to say it is good stuff to work with, low friction and it dries off. Edited July 16, 2016 by embee Link to post
Andy m 23,544 Posted July 17, 2016 Share Posted July 17, 2016 Washing up liquid contains salt so promotes corrosion. You want either tyre lube or a block of hand soap and a cheese grater if you are in a position to choose. Helps if everything is warm too, so leave everything out in the sun while you set your stall out. A G clamp to hold the opposite side in the well can be useful. Andy Link to post
ncmf 87 Posted July 17, 2016 Author Share Posted July 17, 2016 Thanks chaps. I got the front done yesterday after 2 more punctures! I have done plenty of tubeless on the NC but these knoblies were really tight. Needed help in the end. And a lot of care with the levers. It's really hard to get the tyre in the well of the rim as these tyres are so stiff and the rims are quite flat anyway. Thanks for all the help. 1 Link to post
Guest sykospain Posted July 17, 2016 Share Posted July 17, 2016 Murray's described procedure is exactly what I was taught decades ago in a tire bay whilst doing vacation labouring in L.A. Never fails. And don't use Fairy Liquid - use the proper lube goo and carry it witya along with your repair kit if you ride on tubed tires. Link to post
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now