bob b 283 Posted November 27, 2017 Share Posted November 27, 2017 (edited) My Honda original equipment heated grips fail to operate, but the small red indicator light operates as completely as usual. My downloaded workshop manual does not have a wiring diagram, so I am working blind....as it were. I've checked every fuse in the fuse box and taken every connector apart that I've found under the left hand panel and sprayed them with switch cleaner. Still no joy. I'm assuming that there must be a relay somewhere that's 'dicky'. Although I don't know where that's located. If someone could identify the location of the relay, I can clean the connections on that and can carry out an electrical test if necessary. Any pointers would be much appreciated. Edited November 27, 2017 by bob b Additional text Link to post
Guest bonekicker Posted November 28, 2017 Share Posted November 28, 2017 bob b I thought there was a downloadable wiring diagram? some one will help you out later hopefully. Link to post
rjp996 1,091 Posted December 5, 2017 Share Posted December 5, 2017 if its the Honda standard using the aux wiring loom - the relay is on the fuse box left hand side 1/3rd way down - has a fuse directly above it laying flat Link to post
bob b 283 Posted December 8, 2017 Author Share Posted December 8, 2017 Many thanks for that information Richard. I'll check it out over the weekend and post my findings. Link to post
Guest gameboer Posted December 8, 2017 Share Posted December 8, 2017 How many miles did they last? Just wondering when mine will fail Link to post
bob b 283 Posted December 9, 2017 Author Share Posted December 9, 2017 Well, spent a few hours on it, and there isn't any relay in the fuse box at all by the way, I did manage to find an in-line 5 amp fuse buried deep within the bodywork, that checked out fine. So I have decided to live without the bleedin' things. Many thanks for the responses. Link to post
steve-a 97 Posted December 11, 2017 Share Posted December 11, 2017 I had the Honda OEM heated grips on my Integra, they also failed to work half way through last winter, giving the cost of the things it is not great TBH, I just got a set of Bar Muffs instead of replacing them as they work better anyway. Link to post
TheEnglishman 401 Posted December 16, 2017 Share Posted December 16, 2017 Mine went. The wires that go to the throttle grip failed right where the wire joins the grip. I used a dremmil to open the grip up a bit, soldered on new wire, filled the hole with silicone rubber and made the wire exit point significantly more substantial. It's all easy to test as the whole grip wiring is just one big serial loop. The current goes out thought the clutch grip, across the bike then through the throttle grip so continuity is easy to test with a multimeter Good luck! Or hope Santa brings you some Oxfords.... Link to post
rjp996 1,091 Posted December 27, 2017 Share Posted December 27, 2017 On 09/12/2017 at 17:53, bob b said: Well, spent a few hours on it, and there isn't any relay in the fuse box at all by the way, I did manage to find an in-line 5 amp fuse buried deep within the bodywork, that checked out fine. So I have decided to live without the bleedin' things. Many thanks for the responses. Sounds like the dealer (if it was a dealer) that fitted them cheaped out on fitting the proper accessory harness and wired it in 'old school ' Link to post
The Possum 33 Posted December 29, 2017 Share Posted December 29, 2017 I got the Oxford adventures off Amazon (instructions in German) and the oxford handle bar muffs. Really easy to fit and now toasty paws! If you can't find the fault just swap them out. Link to post
Trumpet 216 Posted January 16, 2018 Share Posted January 16, 2018 (edited) Curiously the Honda heated grips are currently unavailable to purchase for the NC750X. I suspect they are having problems .. Edited January 16, 2018 by Trumpet Link to post
Trumpet 216 Posted January 20, 2018 Share Posted January 20, 2018 (edited) Got the accessory loom, got the relay and the 7.5A fuse, got the connectors to plug into said loom. Not sure whether to wait for Honda to get their act together and fix their issues with their heated grips or stick to the Oxford variety .. Edited January 20, 2018 by Trumpet Link to post
TheEnglishman 401 Posted January 27, 2018 Share Posted January 27, 2018 Oxford. I regret getting the honda ones. But since I got muffs I haven't had really cold hands. Link to post
bob b 283 Posted February 24, 2018 Author Share Posted February 24, 2018 On 16/12/2017 at 08:43, TheEnglishman said: Mine went. The wires that go to the throttle grip failed right where the wire joins the grip. I used a dremmil to open the grip up a bit, soldered on new wire, filled the hole with silicone rubber and made the wire exit point significantly more substantial. It's all easy to test as the whole grip wiring is just one big serial loop. The current goes out thought the clutch grip, across the bike then through the throttle grip so continuity is easy to test with a multimeter Good luck! Or hope Santa brings you some Oxfords.... Many thanks for the pointer Neil. That is exactly where my fault turned out to be. As the weather has turned unusually artic down here in the home counties, I thought I had better set to and find this fault. I found it using my continuity meter working around the various circuits. Of course it does make sense (with hindsight) that the fault would probably be there, as that is where the cable is flexing back and forth when using the throttle and a weakness will develop. I should have followed Neil's tip and started at the throttle grip first. I carefully cut away a small part of the throttle grip to expose the severed cable end and I also soldered in an extra length of wire to prevent the 'tugging' as the throttle is twisted. Instead of filling the hole in the grip with silicone rubber afterwards, I used some 'Sugru' to fill and also strengthen the weak point. I introduced some slack into the cable as well before cable tying it in place. I hope that Neil and my findings may help someone else in the future. Link to post
Tyler 108 Posted February 24, 2018 Share Posted February 24, 2018 Thanks for the info, I'll keep an eye on mine just incase they look like failing. Link to post
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now