Guest EasyTiger Posted January 21, 2014 Share Posted January 21, 2014 I have been looking for a "How To" on this anywhere on the forum, or any tips from those who have done it themselves. For a 2012 X DCT..... The part no. for the clutch oil filter is 15412-MGS-D21, (£6.50), (Fowlers' prices 21/01/14). and for the O-RING 39.8 X2.2 9AR 1302-PA9-003 (£2.80) Regular engine oil filter 15410-MJC-505 (£9.58) and washer drain plug 94109-12000 (£0.59) if you want to go the whole way................ Plugs are 2 X IFR6G11K (£19.13 each) Air Filter 1721MGSD30 (£29.82) VAT on top.... Link to post
ste7ios 469 Posted January 21, 2014 Share Posted January 21, 2014 There is no clutch oil. Just two filters, one for the engine, and a smaller for the DCT. Link to post
Derek_Mac 1,404 Posted January 21, 2014 Share Posted January 21, 2014 (edited) As Stelios says, just change the engine oil and both filters. Edited January 21, 2014 by Derek_Mac Link to post
embee 7,288 Posted January 21, 2014 Share Posted January 21, 2014 I've got the oil change bits sitting here waiting for when I get round to putting it back on the road, March hopefully (weather permitting). DCT clutch filter is simple, just go easy with the fasteners on the cover, I've read a report somewhere of someone distorting or cracking the cover. Don't lose the spring, and make sure the filter goes in the right way round (seal one end). Good exploded diagrams and part numbers at http://www.bike-parts-honda.com/# The workshop manual indicates it's very simple, filter is marked "outside" opposite end to the seal, and to be sure it says "this side and spring towards filter cover", can't be much clearer! It just says take cover off, remove spring, remove/replace filter and cover O-ring smeared with oil, fit spring and refit cover. I find such O-rings are usually re-usable a couple of times, but they aren't expensive so ........ Plugs are iridium tipped, will last at least 30k miles and more likely 50k. They can be got from NGK suppliers elsewhere a bit cheaper, like £14 or so(caution, there are fake NGK plugs sold by unscrupulous sorts, use a known supplier like http://spark-plugs.co.uk/ or similar, they are a good supplier I've used, no connection) There was an advert on that auction site from Pidcocks Honda for air filters at about £24 inc (free p&p) if I remember corectly. Link to post
Guest EasyTiger Posted January 21, 2014 Share Posted January 21, 2014 Thanks for these replies and the tips. I had already downloaded the Workshop Manual, but couldn't unzip it in my all-Mac house... I think I must naively have believed there was a separate reservoir for the clutch from the explanation a dealer gave me for the vastly increased price for a 16,000-mile service over the 8... Link to post
Mike5100 2,061 Posted January 15, 2016 Share Posted January 15, 2016 (edited) I take it that the dct filter is item 5 above and it's behind the plate marked 3.? Don't suppose there's any chance of me replacing this without emptying all the engine oil first? Mike Edited January 15, 2016 by Mike5100 Link to post
embee 7,288 Posted January 16, 2016 Share Posted January 16, 2016 Yes Mike, no problem with taking the DCT filter out, only a small amount of oil comes out, a couple of spoonfuls. I didn't renew the O ring but that's your decision. Link to post
Mike5100 2,061 Posted January 16, 2016 Share Posted January 16, 2016 Thanks Embee. I may just get the dealer to post me one and do it myself. Mike Link to post
Guest Number14 Posted January 16, 2016 Share Posted January 16, 2016 (edited) Yes Mike, no problem with taking the DCT filter out, only a small amount of oil comes out, a couple of spoonfuls. I didn't renew the O ring but that's your decision. Just make sure the bike is on the side stand, otherwise the couple of spoonfuls could be bloody big ladels. Edited January 16, 2016 by Number14 Link to post
makman 975 Posted January 23, 2018 Share Posted January 23, 2018 Blast from the past thread that answers my question! I changed the clutch plates on my FJ1200 with it on the side stand and leaning over a touch more down the slope. Just a dribble of oil and change plates over in the pissing rain storm that just decided to blow up from nowhere. Island weather sucks! I'm about to change over my DCT oil filter this weekend. The K&N will be done at a later stage. I'll lean over over a touch more down the slope and change DCT filter then. They are tiny!!!! £6 from M&P online via that website. 1 Link to post
embee 7,288 Posted January 23, 2018 Share Posted January 23, 2018 (edited) No worries with the DCT filter Gordon. The only oil which comes out is the small amount in the filter housing itself, plus a little from the oilways inside I suppose. It doesn't connect into the main chamber inside the engine/gearbox where the bulk oil sits. As you say, they are small, it's just a second line defence against any bits getting into the sensitive solenoid valves, it's supplied with filtered oil from the main engine supply anyway so any bits and pieces should have been dealt with already, belt and braces. I've changed mine 3 times and haven't replaced the O-ring yet, it seems fine (I have a back-up spare in case). Edited January 23, 2018 by embee 2 Link to post
SteveThackery 3,090 Posted January 23, 2018 Share Posted January 23, 2018 On 21/01/2014 at 22:18, Guest EasyTiger said: I think I must naively have believed there was a separate reservoir for the clutch from the explanation a dealer gave me for the vastly increased price for a 16,000-mile service over the 8... I think it's because they check the valve clearances at 16,000 miles. Link to post
elbee 754 Posted January 23, 2018 Share Posted January 23, 2018 1 hour ago, embee said: I've changed mine 3 times and haven't replaced the O-ring yet, it seems fine (I have a back-up spare in case). I changed mine at the 600 mile service (which is fully documented/receipts etc) ... but I kept the old one for future use when out or warranty. Link to post
trisaki 2,029 Posted January 23, 2018 Share Posted January 23, 2018 Just change both filters at the same saves the hassle of doing them separately 1 Link to post
TheEnglishman 401 Posted January 27, 2018 Share Posted January 27, 2018 On 23/01/2018 at 14:42, trisaki said: Just change both filters at the same saves the hassle of doing them separately This. Link to post
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now