Guest Scottiebw Posted July 11, 2014 Share Posted July 11, 2014 After a decent weekend of riding my brake light now appears to be on constantly. I'm guessing this is a dirt in a sensor type scenario. Can anyone advise on where to start cleaning / looking to remedy this? Link to post
JaseR 213 Posted July 11, 2014 Share Posted July 11, 2014 I had a similar issue - corrected by lifting the rear brake pedal and it went off. Washed the offending area (dried as well as possible) and applied ACF50, never had a problem after Link to post
Solution chris 357 Posted July 11, 2014 Solution Share Posted July 11, 2014 There're switches connected to both front brake lever & brake pedal. Most likely is as JaseR says - one of them is stuck. They're the first places to check. According to the manual you need to take the side panel/shroud off but you can probably get enough access to check without doing that Link to post
embee 7,288 Posted July 11, 2014 Share Posted July 11, 2014 As the others say, first things first. Check that both front and rear brake levers are free and returning to their stops properly. Rear is much more likely to be a culprit than front, but check both. Lube the pivots as necessary (if you haven't done it already they'll probably be near enough dry out of the factory). Next step is a quick check as to which switch is doing it, the easy one to get to is the front, under the brake lever pivot area, a small box-like object with 2 wires. Disconnect one (or both) wires and see if the lamp is still on. The more usual issue with these front switches is that the contacts can get a bit dirty and the lamp doesn't come on at all (or only sometimes). Then check the rear switch similarly. The rear switches usually have a threaded body and can be adjusted to set the amount of pedal travel at which the lamp comes on. It's possible that yours was set very close to the pedal off position and settling in has pushed it just into switching on. Link to post
Guest Scottiebw Posted July 11, 2014 Share Posted July 11, 2014 Cheers, I'll give the suggestions a crack. Link to post
Guest bonekicker Posted July 11, 2014 Share Posted July 11, 2014 Scott I would think ACF50 would be a little too thick and sticky for switches just use WD40 ( just my humble opinion) Link to post
Guest Steve700x Posted July 11, 2014 Share Posted July 11, 2014 After a decent weekend of riding my brake light now appears to be on constantly. I'm guessing this is a dirt in a sensor type scenario. Can anyone advise on where to start cleaning / looking to remedy this? Don't kill me for asking this, but you have got the engine on whilst checking this? I thought mine was stuck on when I was cleaning the bike, then realised it won't return until the engine is running. Felt daft! Link to post
Guest Scottiebw Posted July 13, 2014 Share Posted July 13, 2014 Don't kill me for asking this, but you have got the engine on whilst checking this? I thought mine was stuck on when I was cleaning the bike, then realised it won't return until the engine is running. Felt daft! The brake light comes on as soon as the key is in accessory mode and remains on when the engine is running. Just stripping it now to give it a good clean. Link to post
Guest Steve700x Posted July 13, 2014 Share Posted July 13, 2014 The brake light comes on as soon as the key is in accessory mode and remains on when the engine is running. Just stripping it now to give it a good clean. Ok good luck with releasing it then. Just wondered because I found the brake not returning and the realised that once I was riding it, the light was going off. Link to post
chris 357 Posted July 13, 2014 Share Posted July 13, 2014 Ok good luck with releasing it then. Just wondered because I found the brake not returning and the realised that once I was riding it, the light was going off.Sounds like you might have a sticky switch yourself. Engine on or off has no bearing on the circuit but if the switch is sticky the vibes from engine and movement could be enough to cause the sticky one to close. Link to post
michael 324 Posted July 17, 2014 Share Posted July 17, 2014 Discovered the same problem….the rear brake light switch had somehow become maladjusted. (and here I thought it was only the rider that's maladjusted) Simple turning of the switch-it is threaded, and the problem was solved. Good thing too. The relief at finding (with the help of my riding partner, whom merely kneeled down beside the bike and pointed at the switch, telling me in a soft voice, "it's usually the brake light switch.") a simple solution while 300 miles from home on the first day of a week long ride was palpable. <whew> Link to post
Guest Scottiebw Posted July 17, 2014 Share Posted July 17, 2014 Sorry for the delay in responding. It was indeed the rear switch that had got mucked up. A geed clean and wipe and it's working perfectly now. I'd taken the casing off but realised I needn't have. All good. Thanks for the help. Link to post
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now