Guest wandw Posted December 19, 2016 Share Posted December 19, 2016 Finally mine it is fixed the same bolt item number 6 had sheared, Honda in Antibes admitted it was a rare but known fault. All the other work improved the ride and reduced the instances of the gear dropping out, their advice was to ride it in sport mode until they could take it in and that helped dramatically but the fault still occurred. The weird "pump cycle" noise when braking is associated with it so that has gone too and the ride is smoother less gear selection. A lot of frustration - but very happy now. Link to post
Huskyteer 1,091 Posted December 20, 2016 Author Share Posted December 20, 2016 Good to know! Link to post
ade 139 Posted February 11, 2017 Share Posted February 11, 2017 (edited) So this problem happened to me for the first time yesterday on my nc 700 integra. I use the bike everyday commuting through london and also do a fair number of longer trips. Twice On acceleration the gear indicator disappeared on the screen and replaced by a single horizontal line. Power reduced and sticks in a single gear. Unable to switch to s,d, or manual. Switching the ignition off and then on again seemed to resolve the issue. 1. Is this mainly happening to integra's which seems strange.? 2. Does staying in s mode make a difference? 3. Has the reset been a long term solution for anyone? 4. Has anyone had a long term fix? 5. Any other thoughts or suggestions. To resolve this issue or is it something I'm going to live with. Edited February 11, 2017 by ade Link to post
grhhm 6 Posted February 12, 2017 Share Posted February 12, 2017 22 hours ago, ade said: 3. Has the reset been a long term solution for anyone? 4. Has anyone had a long term fix? 5. Any other thoughts or suggestions. To resolve this issue or is it something I'm going to live with. 3. No. 4. Yes. 5. Take the Integra to garage or official dealer. They replace broken/damaged part in the gear box. Link to post
Guest ED MEHR Posted February 14, 2017 Share Posted February 14, 2017 I’m having the same problem with my bike as well. The re occurrence became annoying when I had an oil change out of the agency. So I had the next oil change done by the local agent here in Abu Dhabi, but found no real improvement. Does anyone have a remedy to this problem? Link to post
Guest ED MEHR Posted February 14, 2017 Share Posted February 14, 2017 On Monday, September 01, 2014 at 17:25, Huskyteer said: That's a good point - I try to change down before overtaking, but sometimes I get a bit overexcited and let the bike sort it out I've done 34,000 miles - not sure how many of the DCT NCs have got that far yet, so I may be a pioneer here! I have done 41,000 km & have been having this problem off & on for the last ~20,000 km. Link to post
embee 7,288 Posted February 14, 2017 Share Posted February 14, 2017 As discussed before, my guess is poor contacts somewhere. I had a problem with this on the connector block supplying the right side kill switch/start switches, I'm sure similar tarnished pins in the connector for the gear shift switches could cause such intermittent problems. Try to get to as many of the connectors as you can, but especially the ones for the left and right side handlebar switch blocks which both have gear related switches. Take them apart, see if there is any sign of tarnishing, the pins should be bright and shiny (a couple on mine were very dull and tarnished looking). Use some contact cleaner and work the connectors in/out a few times to get good contact, gently scrape the pins with a small sharp tool if necessary. Apply suitable lube, dielectric grease, ACF50 or even Vaseline to avoid tarnishing in future. If possible you could do the other relevant connectors on the gearbox sensors, there are some under the cubby box on top of the gearbox, plus various ones down near the gearshift motor on the left side at the bottom of the engine, near the gearbox chain sprocket cover. You may need to remove the cover (different arrangement on the Integra/S/X). Link to post
Guest ED MEHR Posted February 15, 2017 Share Posted February 15, 2017 On Monday, February 02, 2015 at 20:13, Huskyteer said: Dobles is awaiting delivery of a sensor. I hope this is the Definitive Broken Thing I was after. And that my days of going to work on the bus are numbered... I think the rear abs proximity sensor is the problem. I think that as we change the rear tire it's wire gets stretched & breaks from the inside. Link to post
Guest ED MEHR Posted February 15, 2017 Share Posted February 15, 2017 5 minutes ago, ED MEHR said: I think the rear abs proximity sensor is the problem. I think that as we change the rear tire it's wire gets stretched & breaks from the inside. On my 15 minute ride to work today I had to stop twice to reset the computer. This is getting bad. I repositioned the rear ABS sensors wire to see if I notice an improvement in the reoccurrence of the glitch. Link to post
Guest ED MEHR Posted April 15, 2017 Share Posted April 15, 2017 OK everyone, I've got the solution to the DCT stuck in gear problem, or the flashing dash in place of the gear indicator. Anyone intrested to know what it is? Link to post
Tex 36,817 Posted April 15, 2017 Share Posted April 15, 2017 1 hour ago, ED MEHR said: OK everyone, I've got the solution to the DCT stuck in gear problem, or the flashing dash in place of the gear indicator. Anyone intrested to know what it is? Buy a manual? 1 Link to post
Guest machinman Posted April 15, 2017 Share Posted April 15, 2017 2 hours ago, ED MEHR said: OK everyone, I've got the solution to the DCT stuck in gear problem, or the flashing dash in place of the gear indicator. Anyone intrested to know what it is? Buy a new bike 🤡 Link to post
pjm 6,041 Posted April 15, 2017 Share Posted April 15, 2017 I have gone blue holding my breath waiting for the answer😧😧 1 Link to post
Guest Nick.Stoner Posted April 24, 2017 Share Posted April 24, 2017 (edited) My NC700XD had those problems too. I've changed oil and filters few times in a year, thinking that it would be a problem with dirt in oil... But at Warsaw Honda Plaza, they asked me at first if I changed sprocket wheels and chain due to run. Of course i've done that, 16000km ago.... So they Counted tooths in sprocket and there is first suspect: rear sprocket wheel in DCT, should have 39 toothl insteat 43, as I have. DCT ECU is going crazy Today I'm going to change to proper sprocket. Edited April 24, 2017 by Nick.Stoner Link to post
Guest Hati Posted April 24, 2017 Share Posted April 24, 2017 51 minutes ago, Nick.Stoner said: My NC700XD had those problems too. I've changed oil and filters few times in a year, thinking that it would be a problem with dirt in oil... But at Warsaw Honda Plaza, they asked me at first if I changed sprocket wheels and chain due to run. Of course i've done that, 16000km ago.... So they Counted tooths in sprocket and there is first suspect: rear sprocket wheel in DCT, should have 39 toothl insteat 43, as I have. DCT ECU is going crazy Today I'm going to change to proper sprocket. So you don't check first what the manual recommends as a replacement? Link to post
Guest Nick.Stoner Posted April 24, 2017 Share Posted April 24, 2017 Not me. Service checked but didn't know that DID catalogue does not recognize between NC700 with DCT or Manual. if You have Nc700X/S DCT then you must choose sprocket for Integra... Strange.. very strange. Now I've learned. Link to post
Guest Nick.Stoner Posted May 21, 2017 Share Posted May 21, 2017 Sprocket replaced, but errors still apears, but now randomly. next suspect is front wheel ABS sensor, because now its completly broken. [and cannot change gears without it. Link to post
ade 139 Posted May 22, 2017 Share Posted May 22, 2017 (edited) I've. Just had a big old service on my integra 700. I mentioned the issue with the sticking gear to the service team. It seems that the integra has been the main culprit for this fault though it has occurred on a few of the other nc bikes with dct. I wondered if it's because it is the heaviest of the nc range. Maybe this is one of the reasons the aluminium swing arm was put on the integra 750. No mention of a problem with the vfr's or Africa twin with dct. Anyway I took the plunge and agreed to have the work done on the gear box. I can't bring myself to say how much. It cost me an arm and a leg, but day 4 post work and 300 more miles on the clock it's like riding a new bike. It actually feels better than when I bought it second hand with 3500 on the clock 22,000 miles ago. So I'm all ready for my trip down to Lyon and the French alps, starting Saturday. It sounds like some of the parts have been upgraded. I'm sorry that my knowledge of the actual fault is a bit vague, I may have been stung but the integra now works like a dream ( not the honda super dream of my youth!!!) Actually It fealt much nicer the the new nc s I had on loan ( personal opinion). So these are the bits that were changed. Pin shifter. Shifter drum Centre shift drum pAwl b ratchet plate change guide spindle comp, gearshift spring, gearshift return pawl a ratchet i hope this means something to the engineers out there. It has definately done the job and I can vigorously accelerate again (in an integra sort of way) without the gear sticking and then having to reset by turning the ignition off and on again Viva integra. Edited May 22, 2017 by ade 4 Link to post
Taipan 110 Posted May 24, 2017 Share Posted May 24, 2017 On 2017-4-15 at 09:44, ED MEHR said: OK everyone, I've got the solution to the DCT stuck in gear problem, or the flashing dash in place of the gear indicator. Anyone intrested to know what it is? I am!! 1 Link to post
Guest ArturP Posted September 28, 2018 Share Posted September 28, 2018 On 15/04/2017 at 09:44, ED MEHR said: OK everyone, I've got the solution to the DCT stuck in gear problem, or the flashing dash in place of the gear indicator. Anyone intrested to know what it is? I am interested. Link to post
Guest osis Posted April 9, 2019 Share Posted April 9, 2019 Hi guys, My nc700d integra is showing D and S at the same time and I can't switch between D and S or put in manual mode. Any ideas? Thank you in advance Link to post
Tonyj 6,907 Posted April 9, 2019 Share Posted April 9, 2019 Shift pin , see Murray’s post , good start. Link to post
embee 7,288 Posted April 10, 2019 Share Posted April 10, 2019 (edited) I had a very quick glance at the service manual but couldn't find the DS fault mentioned, it may well be in there somewhere, it's a fairtly big section. Have you tried disconnecting the battery for half an hour or so? Easy thing to try and you never know, "switch it off, switch it back on again". I seem to recall it does a DS thing when you do the DCT clutch initialisation procedure, so that would be worth a try too, it might just prompt it to do something, and it's free. Otherwise you could do with getting it into the diagnostic mode and see if there are any fault codes. You don't also have an ABS fault showing by any chance? When was the shift pin done? That requires some things to be disconnected so worth checking the connectors. The clutch side cover comes off so all the sensors on that are unplugged, the oil pressure sensors, shift shaft position sensor etc, plus the shift motor is taken off on the other side so that gets unplugged too. Edited April 10, 2019 by embee 1 Link to post
Guest osis Posted April 11, 2019 Share Posted April 11, 2019 Thank you Pin was changed just a week ago, I'm sure they didn't take shift motor off, all the plastics were on that side, there are fault codes but my garage can't clear them so I need to put everything back together and take it somewhere else in London. Any suggestions where to? I'm also missing metal footrest bracket maybe someone has one that I could buy? The good thing I have a spear engine with all the sensors and injectors if anyone need, it has done 7000miles. Link to post
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now