prr 153 Posted June 11, 2015 Share Posted June 11, 2015 Changing just the chain without the sprockets wouldn't be the best thing to do. At the same time mine chain was always lubed and still failed. I suppose it is because of my a bit more aggressive riding style. Link to post
Mike5100 2,061 Posted June 11, 2015 Share Posted June 11, 2015 17500 miles on my chain and sprocket so far and only adjusted it once. I bought a new sprocket so I had something to compare the old one to. It's hardly worn. Maybe I just got lucky. Ride in all weathers and oil my chain with 80W/90 gear oil using an old fashion style oil can every other day (150 miles) when I get home, definitely better to do this with a warm chain. Removed the Tutoro oiler as it was getting all gunked up around the swing arm. Just my 2 pence worth. Chris Chris - I am tempted to try this technique as it is easy to flip the centre stand down and rotate the wheel by hand and it takes maybe 30 seconds to get oil on all the rollers. But - the messy part is always getting protection on the side-plates of the chain which on both my standard oem chains have gone rusty pretty quickly. Do you pay any attention to the side plates? Mike Link to post
Guest chicken george Posted June 11, 2015 Share Posted June 11, 2015 Changing just the chain without the sprockets wouldn't be the best thing to do. At the same time mine chain was always lubed and still failed. I suppose it is because of my a bit more aggressive riding style. I measured my rear sprocket and compared it to my new one and there is hardly any ware at all. So why would I need to replace it? Chris - I am tempted to try this technique as it is easy to flip the centre stand down and rotate the wheel by hand and it takes maybe 30 seconds to get oil on all the rollers. But - the messy part is always getting protection on the side-plates of the chain which on both my standard oem chains have gone rusty pretty quickly. Do you pay any attention to the side plates? Mike Mike, During the winter months I did pop some oil on a rag and run it over the side plates after I had cleaned the bike and chain (mostly weekly). But I haven't needed to for ages. If you look really close they have a spot surface rust. I think the chain will stretch and/or joints will seize up before the chain side plates rust enough to worry about. Cheers Link to post
prr 153 Posted June 12, 2015 Share Posted June 12, 2015 As soon as the sprocket is wear it will quickly damage the chain as well. And the chain is the more expensive part. More info about the sprocket wear HERE Link to post
Guest chicken george Posted June 13, 2015 Share Posted June 13, 2015 I'm not an expert on this matter but I disagree. However, if I'm wrong then it's going to cost me more money in the long run. So, if I change my chain (myself) and leave the sprocket, which is no where near worn, then its going to cost £70. If I change both, because the sprocket "will" wear out in the future, then it will cost me £110. I check my rear sprocket every time I oil the chain. So I hope I'd spot when it gets close to need replacing. Chris Link to post
aquaboy 105 Posted June 21, 2015 Share Posted June 21, 2015 Its the gearbox sprocket that wears the most, and that's cheaper Link to post
prr 153 Posted June 26, 2015 Share Posted June 26, 2015 Finally I got a call from Honda dealer and they are changing the chain next Thursday. Meanwhile I bought a second bike ... for track days - CBR F4i Link to post
prr 153 Posted July 2, 2015 Share Posted July 2, 2015 Chain and sprockets changed under warranty at 19371kms. The clock too. Link to post
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now